NACE-CIP1-001

Your FIRST preferred course of action is to:

First post and replies  | Last post by Rueben, 7 months ago

Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:

First post and replies  | Last post by Esteban, 7 months ago

Conventional spray is a good choice when:

First post and replies  | Last post by Isaiah, 7 months ago

Inspection documentation is important because:

First post and replies  | Last post by Theo, 7 months ago

In a non-convertible coating the role of the primary solvent is to:

First post and replies  | Last post by Antwan, 7 months ago

What is used to determine compressed air cleanliness?

First post and replies  | Last post by Tuan, 7 months ago

It is good practice for the NACE Inspector to have instrument calibration certificates available:

First post and replies  | Last post by Isaiah, 7 months ago

The form of corrosion that has the largest potential for unexpected catastrophic failure is:

First post and replies  | Last post by Harris, 7 months ago

When holiday testing is required the Inspector is always required to enforce NACE SP 0188:

First post and replies  | Last post by Brain, 7 months ago

If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:

First post and replies  | Last post by Randolph, 7 months ago

Non Conformance Reports are completed by the Inspector:

First post and replies  | Last post by Antwan, 7 months ago

To achieve consistently accurate results with ALL alt test equipment

First post and replies  | Last post by Guillermo, 7 months ago

Removal of welds splatter is required:

First post and replies  | Last post by Dante, 7 months ago

What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?

First post and replies  | Last post by Manual, 7 months ago

Checking is

First post and replies  | Last post by Gonzalo, 7 months ago

Polymerization is the process of:

First post and replies  | Last post by Chas, 7 months ago

An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called

First post and replies  | Last post by Galen, 7 months ago

Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT

First post and replies  | Last post by Manual, 8 months ago

When applying Thermal Spray Coatings the specification is most likely to refence:

First post and replies  | Last post by Randolph, 8 months ago

Upon arrival of coating materials, the inspector should

First post and replies  | Last post by Wilber, 8 months ago

When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:

First post and replies  | Last post by Rolando, 8 months ago

If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a

First post and replies  | Last post by Rueben, 8 months ago

Your FIRST preferred course of action is to:

First post and replies  | Last post by Rueben, 8 months ago

Osmotic blistering is most likely to occur as a result of

First post and replies  | Last post by Guillermo, 8 months ago

An inspectors personal log book should contain:

First post and replies  | Last post by Coy, 8 months ago

Galvanic corrosion occurs on which of the following substrates:

First post and replies  | Last post by Rashad, 8 months ago

The initial steel condition is important to the NACE Inspector because:

First post and replies  | Last post by Lloyd, 9 months ago

Relative humidity is

First post and replies  | Last post by Zachariah, 9 months ago

Fine cracks in the surface of a coating that rarely reach the substrate are called

First post and replies  | Last post by Brain, 9 months ago

Dew point is the temperature at which

First post and replies  | Last post by Brain, 9 months ago